The Cisco 300-510 SPRI (Implementing Cisco Service Provider Advanced Routing Solutions) certification exam is a critical step for network professionals aiming to validate their expertise in advanced routing solutions for service provider networks. This exam tests your knowledge of implementing, troubleshooting, and optimizing core and edge routing technologies, including BGP, OSPF, IS-IS, MPLS, and Segment Routing. To help you prepare, I’m sharing 15 free practice questions from a recently updated bank of 210 practice questions available on my resource website(https://www.pass4itsure.com/300-510.html). These questions are designed to simulate the exam experience and reinforce key concepts.

Latest 300-510 SPRI practice questions shared online

Number of exam questions	Related
15 (Free)	CCNP Service Provider

Question 1:

What is enabled by default on Cisco IOS-XR routers and cannot be disabled?

A. SSH server

B. Multicast routing

C. IPv4 and IPv6 CEF

D. IPv6 routing

E. CDP

F. BFD

Correct Answer: C

Before using the BGP policy accounting feature, you must enable BGP on the router (CEF is enabled by default).

Question 2:

Refer to the exhibit.

While configuring router 2 with all the default values, a network engineer cannot see any route received in router 1. How should the engineer solve the issue?

A. Set up a priority different than 0 in the interface.

B. Modify the router ID to be the interface IP on the serial.

C. Modify the IP address or mask of the interface to a valid one.

D. Set the network type in S1/0 to point-to-point.

Correct Answer: C

---

Question 3:

What can be used to determine a path from the head-end to a tail-end router when implementing SR-TE with a head-end, with little information on the network topology?

A. traffic controller

B. path computation engine

C. tail-end router

D. SNMP server

Correct Answer: B

Question 4:

Refer to the exhibit

A network engineer installed a new router (router 3) at the regional hub running MPLS services for scalability Router 3 is connected to the 10.44 4.0/24. 10.44 5.0/24. 10 44.6.0/24. and 10 44.7.0/24 subnets

The new router has been configured for OSPF area 2. and it is advertising the four connected networks.

The engineer noticed that the same networks are listed as interarea summary routes, and they are being flooded into each area on the area borders

Which action resolves the issue?

A. On router 3, configure an access list to filter the networks.

B. On router 2, configure a route map to filter the networks.

C. Under the OSPF configuration on router 3. add area 2 range 10.44.4.0 255.255.252.0.

D. Under the OSPF configuration on router 2, add area 2 range 10.44.4.0 255.255.252.0.

Correct Answer: D

Question 5:

Refer to the exhibit.

Customer traffic from the branch site to the hub is experiencing packet drops. The engineer verified that:

1.

Customer traffic from the hub is able to reach the branch site.

2.

The connection between PE1 and PE2 is working normally.

3.

Routers P1 and P2 are able to ping devices on the hub site. Which action resolves the issue?

A. Redistribute the CE1 OSPF routes in the PE1 VRF.

B. Redistribute the CE2 OSPF routes in the PE2 VRF.

C. Advertise the VPNv4 routes of the branch site in CE2.

D. Advertise the VPNv4 routes of the hub in CE1.

Correct Answer: D

Question 6:

Refer to the exhibit.

An engineer working for a private telecommunication company with an employee id: 4233:46:364 notices that the customer network going through AS30-AS65001-AS65000 is experiencing packet drops when it accesses an application at 172.16.20.1/32 In the DC cloud.

The BGP link between AS20 and AS30 is inaccessible because of a fiber cut. Routers RL, RN, and RZ are configured with confederation identifier 10.

Which action resolves this Issue?

A. RX(config)#router bgp 65001RX(config-router)# bgp confederation peers 65000

B. RB(config)#router bgp 30RB(config-router)# neighbor 10.10.10.3 remote-as 65001

C. RM(config)#router bgp 65000RM(config-router)# bgp confederation peers 65001

D. RX(config)#router bgp 65001RX(config-router)# no synchronizationRX(config-router)# bgp confederation identifier 10

Correct Answer: D

Question 7:

Refer to the exhibit.

A network operator must inject a Level 1 route from XR2 (10.16.16.0/24) into the ISIS topology.

Which configuration allows the injection in a way that XR3 and XR1 have a valid and working route for 10.16.16.0/24?

A. Option A

B. Option B

C. Option C

D. Option D

Correct Answer: D

L1 route injected by XR2 won\’t be advertised to XR1, since L2 routes are NOT leaked to L1 by default. An [L2-L1] route leak policy should be configured on L1/L2 router (XR3).

Question 8:

What is the purpose of a BGP confederation?

A. It limits the number of routes a device receives from its peers, which reduces CPU load.

B. It improves service by increasing the number of simultaneous iBGP peering sessions.

C. It redirects traffic away from route reflectors, which reduces their operating load.

D. It reduces the number of iBGP peers and increases stability.

Correct Answer: D

Question 9:

Which feature is used in multicast routing to prevent loops?

A. STP

B. inverse ARP

C. RPF

D. split horizon

Correct Answer: C

Question 10:

What is the difference between basic IS-IS and OSPF packet types?

A. IS-IS and OSPF use area packets, but only IS-IS uses sequence number packets.

B. IS-IS and OSPF use link-state update packets, but only OSPF uses link-state ACK packets.

C. IS-IS and OSPF use Hello packets, but only OSPF uses DBD packets.

D. IS-IS and OSPF use link-state update packets, but only IS-IS uses DBD packets.

Correct Answer: C

Reference: https://www.ciscopress.com/articles/article.asp?p=26850andseqNum=4

Question 11:

Refer to the exhibit.

All routers on this network have been configured with PIM-SM, and R1 is the rendezvous point. However, when asymmetric routing is implemented to modify link usage, the network begins to drop certain multicast traffic. Which action corrects the problem?

A. Place the routes affected by asymmetric routing in a VRF

B. Remove the asymmetric routing and use spanning tree to manage link usage

C. Add a static mroute for routes that are failing

D. Configure the routers to use PIM-DM instead of PIM-SM

Correct Answer: C

Question 12:

Refer to the exhibit.

The extension header of the IPv6 header is ignored when which value is equal to zero?

A. Segments Left

B. Hdr Ext Len

C. Routing Type

D. Next Header

Correct Answer: D

Reference: https://www.ciscopress.com/articles/article.asp?p=31948

Question 13:

After an engineer configures BGP in R1, it starts receiving this message Jun 29 13:30:50.122: %BGP-5-ADJCHANGE: neighbor 192.168.10.1 Down User reset Jun 29 13:30:52.341: %BGP-3-NOTIFICATION: sent to neighbor 192.168.10.1 2/6 (unacceptable hold time) 0 bytes Which action makes the peering come back up again?

A. Make a soft reset to the peer.

B. Set up a minimum hold-down timer higher.

C. Set up a hello timer higher.

D. Set up a hold-down timer higher.

Correct Answer: B

Question 14:

Refer to the exhibit.

Customer A is a small media company with two offices connected by a 512 Kbps line. Their NY office is connected to several external partners by static routes on router R3.

VoIP services use VoIP codec G729 Users reported poor voice quality and slow data transfer between the offices A network engineer configured ip tcp header- compression iphc-format on R2 and R3 routers

Which additional action must the engineer take to fix the issue?

A. Configure the ip ospf I area O command under Serial 1/1 interfaces on R2 and R3 to avoid routing loops

B. Change the OSPF router ID on either router so that the router IDs are unique.

C. Configure the summary-address 10.10.0.0 255.255.240.0 command on R3 to optimize OSPF communication

D. Configure the BGP routing protocol between R2 and R3 to control route propagation.

Correct Answer: C

Question 15:

What is the purpose of ACL type prefix set entries in RPL prefix sets?

A. They hold IPv4 or IPv6 prefixes that do not match specifications.

B. They hold IPv4 or IPv6 prefix match specifications.

C. They hold IPv6 prefix match specifications.

D. They hold IPv4 prefixes that do not match specifications.

Correct Answer: B

How to Use 300-510 SPRI Practice Questions

• Simulate Exam Conditions: Answer the questions in a quiet environment within a time limit to mimic the real exam experience.
• Review Answers and Explanations: Check detailed explanations after each question to understand mistakes.
• Address Knowledge Gaps: Focus on reviewing topics where you’re weak.

Additional Resources

Pass4itsure offers 210 updated practice questions, including single and multiple-choice, drag-and-drop, and simulation labs, covering all topics of the Cisco 300-510 SPRI exam. Study flexibly with PDF or VCE formats. Visit https://www.pass4itsure.com/300-510.html now for more preparation resources!

Total	210
Single & Multiple Choice	198
Drag Drop	8
Simulation Labs	4

Finally, remember that the Cisco 300-510 SPRI certification is a key step to advancing your career in service provider networking. Kickstart your preparation with these 15 free practice questions and visit Pass4itsure for more tools and support. Best of luck on your exam!